[Avila] gw2201 woes

[Mark Kelly]

Chris,

I'm still having issues with the GW2201, I'm currently moving to the
latest stable kernel 2.6.23.12 and seeing if that makes a difference.

Since moving I'm now seeing problems with the ixp400_eth driver
compilation, I'm see this error on compile and can't really figure out
where it's coming from.  Got any ideas?  I also see that intel has
version 3.0 of the driver out, do you have any plans to migrate to it?

WARNING: vmlinux.o(.text+0xce810): Section mismatch: reference
to .init.text:pcibios_setup (between 'pci_setup' and 'pci_init')
  GEN     .version
  CHK     include/linux/compile.h
  UPD     include/linux/compile.h
  CC      init/version.o
  LD      init/built-in.o
  LD      vmlinux
drivers/built-in.o: In function `ixErrHdlAccEthNPERecoveryJob':
IxNpeMicrocode.c:(.text+0x45900): undefined reference to
`ixParityENAccParityNPEConfigReUpdate'
drivers/built-in.o: In function `ixErrHdlAccEthNPEHandleISR':
IxNpeMicrocode.c:(.text+0x459dc): undefined reference to
`ixParityENAccNPEParityErrorCheck'
IxNpeMicrocode.c:(.text+0x45a68): undefined reference to
`ixParityENAccParityErrorInterruptClear'
drivers/built-in.o: In function `ixOsalOsIxp400VersionGet':
IxNpeMicrocode.c:(.text+0x45bf0): undefined reference to
`system_utsname'
drivers/built-in.o: In function `ixOsalOsIxp400NameGet':
IxNpeMicrocode.c:(.text+0x45c14): undefined reference to
`system_utsname'
make[5]: *** [vmlinux] Error 1

Thanks,

Mark

On Fri, 2007-12-21 at 11:12 -0800, Chris Lang wrote:
> Mark,
> 
> >From first glance, IRQ 28 sounds like the correct IRQ. This is going to
> be dependent on the slot you put the card into, so I don't believe this
> is the problem.
> 
> I would try turing off extended, shar_irq, detect_irq, and many_ports
> 
> On Fri, 2007-12-21 at 09:33 -0500, Mark Kelly wrote:
> > Chris,
> > 
> > I think I see the root of the problem. 
> > 
> > 
> > d# lspci -v
> > 00:01.0 Serial controller: Exar Corp. XR17C158 Octal UART (rev 09)
> > (prog-if 02 [16550])
> >         Flags: fast devsel, IRQ 28
> >         Memory at 48010000 (32-bit, non-prefetchable) [size=4K]
> > 
> > 
> > The board is detected, but it doesn't appear to configured correctly.  
> > 
> > if I look under /proc/irq/28/  no node is being created for the serial
> > board, so it appears to be IRQ related problem I am seeing.
> > 
> > I have compiled the kernel with the following options turned on:
> > 
> > 	CONFIG_SERIAL_8250_PCI=y
> > 	CONFIG_SERIAL_8250_NR_UARTS=10
> > 	CONFIG_SERIAL_8250_RUNTIME_UARTS=10
> > 	CONFIG_SERIAL_8250_EXTENDED=y
> >  	CONFIG_SERIAL_8250_SHARE_IRQ=y
> > 	CONFIG_SERIAL_8250_DETECT_IRQ=y
> > 	CONFIG_SERIAL_8250_MANY_PORTS=y
> > 
> > If I use setserial to configure the IRQ to be 00 and not 28, I get
> > output from the board, but it has missing gaps in the stream.  
> > 
> > 
> > Thanks,
> > 
> > Mark